What Is Upper and Lower Control Limits (UCL and LCL)?

Definition

Upper and Lower Control Limits (UCL and LCL) are the boundaries on a control chart that show the normal range of variation of a stable process. They are calculated from process data, usually at three standard deviations either side of the centre line.

UCL and LCL in Simple Terms

Every process varies a little. Control limits show how much variation is normal for this process. A point outside them, or a non-random pattern inside them, signals that something has changed and the process may be out of control.

Control limits come from the process. Specification limits come from the drawing. The two are not the same thing.

How to Calculate Them

For an X-bar and R chart with subgroups of size n:

  • X-bar chart: UCL = X-double-bar + A2 x R-bar, LCL = X-double-bar - A2 x R-bar
  • R chart: UCL = D4 x R-bar, LCL = D3 x R-bar

A2, D3 and D4 are constants from standard tables. For n = 5, A2 is 0.577, D3 is 0 and D4 is 2.114. Limits should be calculated from at least 20 to 25 subgroups taken while the process is stable.

Example

A shaft diameter is checked in subgroups of five. Over 25 subgroups the grand average is 12.004 mm and the average range is 0.010 mm. UCL = 12.004 + 0.577 x 0.010 = 12.0098 mm and LCL = 11.9982 mm. A later subgroup average of 12.011 mm is above the UCL, so the operator stops and finds a loose tool holder, even though every part is still inside the drawing tolerance.

Common Mistakes

  • Drawing specification limits on the chart and calling them control limits.
  • Recalculating limits after every point, so real shifts are hidden.
  • Ignoring patterns inside the limits that the run rules would flag.

The OperaHive SPC software provides X-bar, R, S and I-MR control charts with alert rules. See the SPC and Cpk guide for more.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What is an upper control limit?

The upper control limit (UCL) is the highest value a stable process is expected to produce on a control chart, usually set three standard deviations above the centre line.

What are UCL and LCL?

UCL and LCL are the upper and lower control limits on a control chart. Points between them show normal variation; points outside them signal a special cause that needs investigation.

How do you calculate UCL and LCL?

For an X-bar chart, UCL = X double bar + A2 x R bar and LCL = X double bar minus A2 x R bar. A2 is a constant that depends on subgroup size.

What is the formula for UCL with standard deviation?

UCL = mean + 3 sigma and LCL = mean minus 3 sigma, where sigma is the estimated standard deviation of the plotted statistic, not of individual parts unless it is an individuals chart.

Control limits vs specification limits: what is the difference?

Control limits are calculated from process data and show normal variation. Specification limits come from the customer or drawing and define acceptable parts.

Why are control limits set at 3 sigma?

Three sigma limits balance two risks: reacting to normal variation too often, and missing real changes. For a stable, roughly normal process very few points fall outside them by chance.

What does it mean when a point is above the UCL?

It means a special cause has probably changed the process. Stop and investigate the cause, such as tool wear, material change or setup error, and record the action taken.

Can the LCL be negative?

For charts of ranges, counts or proportions a negative LCL is set to zero, because those values cannot be below zero.

When should you recalculate control limits?

Recalculate after a deliberate process change, such as a new tool or method, once enough new data is collected. Do not recalculate just because points fall outside the limits.

How many data points do you need to calculate UCL?

A common rule is 20 to 25 subgroups from a stable process. Fewer points give limits that are less reliable and should be treated as provisional.

Put It Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.