What Is Out-of-Control Process?

Definition

An out-of-control process is a process whose output shows variation from special (assignable) causes, as signalled on a control chart by points beyond the control limits or by non-random patterns.

Out-of-Control Process in Simple Terms

Every process varies. Common cause variation is the normal, random noise of a stable process. Special cause variation comes from something specific, such as a worn tool, a new material lot or a wrong setting. When special causes appear, the process is out of statistical control. This is not the same as making bad parts: a process can be out of control and still within tolerance, or in control and making scrap.

How It Is Detected

In SPC, points are plotted against the upper and lower control limits, usually set at three standard deviations from the centre line. Common run rules that signal an out-of-control process include:

  • One point beyond either control limit.
  • Seven or more points in a row on one side of the centre line (some rule sets use eight or nine).
  • Six or more points in a row steadily rising or falling.
  • Two of three points near one control limit.

Example

An X-bar chart for a bore diameter shows seven subgroups in a row above the centre line, though all parts are within tolerance. The operator stops and checks the setup. A new boring bar was fitted from a different supplier and cuts slightly large. The offset is corrected, the reaction is logged and the chart returns to random variation.

Why It Matters

Capability figures such as Cp and Cpk are only meaningful for a process in control. Acting on signals early prevents drift turning into scrap, while leaving a stable process alone avoids over-adjustment. OperaHive SPC software provides control charts with alert rules. See also our SPC and Cpk guide.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What does out of control mean in SPC?

It means the chart shows evidence of special cause variation, through a point beyond the control limits or a non-random pattern, so the process is not stable.

Can an out-of-control process still make good parts?

Yes. Control limits come from process data, not the tolerance. A process can be out of control yet still within specification, but it is less predictable and should be investigated.

What should you do when a process goes out of control?

Follow the reaction plan: stop if required, find and remove the special cause, check parts made since the last good point, and record the action.

What are the rules for an out of control process?

Common rules, such as the Western Electric or Nelson rules, include one point beyond 3 sigma, 7 to 9 points in a row on one side of the centre line, 6 points steadily rising or falling, and 2 of 3 points beyond 2 sigma.

What is the difference between out of control and out of specification?

Out of control means the process shows special cause variation against its control limits. Out of specification means a part is outside the tolerance. A process can be one without the other.

What causes an out of control process?

Typical special causes include tool wear or breakage, a new material lot, a setting change, a measurement error, an untrained operator or changes in temperature.

What is an example of an out of control process?

On an X-bar chart for shaft diameter, eight points in a row fall above the centre line after a tool change. This trend signals a special cause even though all parts are in tolerance.

What is the difference between common cause and special cause variation?

Common cause variation is the natural, random variation built into a process. Special cause variation comes from a specific, identifiable source and makes the process out of control.

Can you calculate Cpk on an out of control process?

You can calculate the number, but it is not meaningful. Capability indices assume a stable process, so bring the process into control first.

Which control charts detect an out of control process?

X-bar and R or X-bar and S charts suit subgrouped variable data, I-MR charts suit single readings, and p, np, c and u charts suit attribute data. Choose by data type and subgroup size.

What is an out of control action plan (OCAP)?

An OCAP is a documented flowchart that tells the operator exactly what to check and do when a control chart signals out of control, including who to call and when to stop production.

Put Out-of-Control Process Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.