What Is Control Chart?

Definition

A Control Chart is a time-ordered graph of process data with a centre line and upper and lower control limits calculated from the process itself. It shows whether a process is stable or affected by a special cause.

Control Chart in Simple Terms

Every process varies a little. A control chart separates normal, common-cause variation from unusual, special-cause variation. Points inside the limits with no patterns mean the process is stable. A point outside the limits, or a pattern such as a long run on one side, means something has changed and should be investigated.

Control charts are the core tool of SPC. The limits, explained in UCL and LCL, usually sit three standard deviations from the centre line and are not the same as specification limits.

Common Chart Types

ChartData typeTypical use
X-bar and RVariable, subgroups of 2 to 9Machined dimensions sampled every hour
X-bar and SVariable, larger subgroupsHigh-volume automated measurement
I-MRVariable, single readingsBatch chemistry, slow processes
p and npAttribute, defectivesPercent of parts rejected
c and uAttribute, defect countsPaint defects per panel

Example

An X-bar and R chart on a shaft diameter shows seven subgroup averages in a row trending upward, although all parts are still in tolerance. The operator checks the tool and finds wear, changes the insert, and the process returns to centre before any parts are scrapped.

Common Mistakes

  • Drawing specification limits on the chart and calling them control limits.
  • Adjusting the process after every point, which adds variation.
  • Recalculating limits too often, so shifts are absorbed.
  • Charting data but not reacting to run rule signals.

The OperaHive SPC software supports X-bar, R, S and I-MR charts with alert rules. See the SPC and Cpk guide for more.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What is the difference between control limits and specification limits?

Control limits come from the process data and show what the process actually does. Specification limits come from the drawing and show what the customer allows.

Which control chart should I use?

Use X-bar and R for measured data in small subgroups, I-MR for single measurements, and p, np, c or u charts for counts of defectives or defects.

What is a control chart in quality control?

A control chart is a time-ordered graph of process data with a centre line and upper and lower control limits. It shows whether a process is stable and helps tell normal variation from special causes.

How do you calculate control limits?

Control limits are usually set at the process mean plus or minus three standard deviations of the plotted statistic. For an X-bar and R chart, they are found from the average range using standard constants such as A2.

What are the Western Electric rules for control charts?

The Western Electric rules flag a process as out of control when, for example:

  • one point falls outside the 3 sigma limits
  • 2 of 3 points fall beyond 2 sigma on one side
  • 4 of 5 points fall beyond 1 sigma
  • 8 points in a row sit on one side
What is a control chart example?

A plant measures five shaft diameters every hour and plots the subgroup average and range on an X-bar and R chart. When a run of averages trends upward, operators find tool wear and change the tool before parts go out of tolerance.

What is the difference between common cause and special cause variation?

Common cause variation is the natural background noise built into a stable process. Special cause variation comes from a specific, identifiable event such as a broken tool or a new material lot, and shows up as signals on the chart.

When should control limits be recalculated?

Recalculate control limits after a deliberate, verified process change, or once enough new stable data exists. Do not recalculate just because points fall outside the limits, as that hides real signals.

What is SPC software for control charts?

SPC software collects measurements, plots control charts in real time, applies run rules and alerts operators to signals. It also calculates capability indices and keeps records for customer audits.

Why do control charts use 3 sigma limits?

Three sigma limits balance two risks: reacting to noise and missing real changes. For a stable, roughly normal process, only about 0.27 percent of points fall outside by chance.

Put Control Chart Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.