What Is Pp and Ppk?

Definition

Pp and Ppk are process performance indices that compare the total spread of a process, using the overall standard deviation, with the specification limits. Ppk also accounts for how well the process is centred.

Pp and Ppk in Simple Terms

Pp asks: if the process were centred, would its total spread fit inside the tolerance? Ppk asks the same question using the nearer specification limit, so an off-centre process scores lower.

The difference from Cp and Cpk is the standard deviation used. Cp and Cpk use within-subgroup variation, which shows short-term potential. Pp and Ppk use overall variation across all data, which includes shifts between subgroups.

How They Are Calculated

  • Pp = (USL minus LSL) divided by 6 times the overall standard deviation.
  • Ppk = the smaller of (USL minus mean) and (mean minus LSL), divided by 3 times the overall standard deviation.
IndexVariation usedTypical use
Cp, CpkWithin subgroupsOngoing capability of a stable process
Pp, PpkOverall, all dataInitial process studies and PPAP

Example

A shaft diameter has a tolerance of 20.00 to 20.10 mm. A run of 125 parts gives a mean of 20.06 mm and an overall standard deviation of 0.008 mm. Pp is 0.10 divided by 0.048, about 2.08. Ppk uses the upper side: 0.04 divided by 0.024, about 1.67. The process is capable but running slightly high.

Why It Matters

The AIAG PPAP manual uses Ppk for initial process studies, with a common acceptance target of 1.67 or higher, and many customers set their own values in customer-specific requirements. A large gap between Cpk and Ppk is a sign of special causes, so check the control chart first. OperaHive SPC software calculates capability from the data collected on the line. Read more in our SPC and Cpk guide.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What is Pp and Ppk?

Pp and Ppk are process performance indices. They compare the overall spread of a process, using the total standard deviation, with the specification limits. Ppk also accounts for how well the process is centred.

What is a good Ppk value?

A Ppk of 1.67 or higher is a common target for initial studies in automotive PPAP, and 1.33 is often used as a minimum. Always check your customer requirements.

How do you calculate Ppk?

Ppk is the smaller of (USL minus mean) divided by 3 times the overall standard deviation, and (mean minus LSL) divided by 3 times the overall standard deviation.

How do you calculate Pp?

Pp equals the specification width (USL minus LSL) divided by 6 times the overall standard deviation. It ignores where the mean sits, so it shows potential performance only.

Ppk vs Cpk: what is the difference?

Cpk uses within-subgroup standard deviation and shows short-term capability. Ppk uses overall standard deviation from all data and shows actual long-term performance, including shifts between subgroups.

Can Ppk be higher than Cpk?

It can happen by chance with small samples, but normally Ppk is equal to or lower than Cpk because overall variation includes between-subgroup shifts.

What is the difference between Pp and Ppk?

Pp only compares spread with the tolerance. Ppk also considers centring, so if the process mean drifts towards one limit, Ppk drops while Pp stays the same.

When should Ppk be used instead of Cpk?

Ppk is used for initial process studies, such as during PPAP, and when the process is not yet proven stable. Cpk is used once the process is in statistical control.

How many samples do you need for a Ppk study?

A common guideline is at least 100 measurements, often 25 subgroups of 4 or 5 parts, taken from a significant production run. Customer requirements may specify more.

What does a negative Ppk mean?

A negative Ppk means the process mean is outside one of the specification limits, so most parts are out of tolerance on that side.

Put Pp and Ppk Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.