What Is Acceptable Quality Limit (AQL)?

Definition

Acceptable Quality Limit (AQL) is the worst average defect rate that a sampling plan treats as acceptable for a series of lots. It sets the sample size and the number of defects allowed before a lot is rejected.

AQL in Simple Terms

Inspecting every part in a large lot is slow and expensive, so many plants inspect a sample instead. AQL is the quality level that sampling plan is built around. An AQL of 1.0 means the plan is designed to accept lots that average about 1 percent defective most of the time.

AQL sampling plans come from standards such as ISO 2859-1 and ANSI/ASQ Z1.4. They are common in incoming inspection and final inspection.

How It Works

  1. Find the lot size and the inspection level (General Level II is the usual default).
  2. Read the sample size code letter from the standard table.
  3. Look up the sample size and the accept and reject numbers for the chosen AQL.
  4. Inspect the sample. If the defects found are at or below the accept number, accept the lot. Otherwise reject it.
Defect classTypical AQLMeaning
Critical0 (zero acceptance)Safety or legal risk, no defects allowed
Major1.0 to 2.5Likely to cause failure or a return
Minor2.5 to 4.0Cosmetic, unlikely to affect use

Example

A plant receives a lot of 1,200 machined bushings. Under General Level II the code letter is J, which gives a sample of 80. At an AQL of 1.0 the lot is accepted with 2 or fewer defectives and rejected with 3 or more. The inspector finds 1 defective, so the lot is accepted and the defective part is segregated.

Common Mistakes

  • Reading AQL as a promise that every lot is under that defect rate. A sample cannot guarantee that.
  • Using AQL sampling for safety-critical or special characteristics, where many customers expect zero defects and 100 percent checks.
  • Ignoring the switching rules to tightened or reduced inspection.

The OperaHive quality inspection software records incoming, in-process and final inspection results and links rejected lots to nonconformances.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What does AQL 2.5 mean?

It means the sampling plan is built to accept lots averaging about 2.5 percent defective most of the time. The exact sample size and accept number come from the standard table for your lot size.

Is a lower AQL stricter?

Yes. A lower AQL allows fewer defects in the sample, so the plan rejects lots more readily.

Is AQL the same as zero defects?

No. AQL accepts that some defective parts may pass in accepted lots. Zero-acceptance plans or 100 percent inspection are used when no defects can be tolerated.

What is AQL in quality control?

AQL, or acceptable quality limit, is the worst average defect rate a buyer will tolerate for lots inspected by sampling. It sets the sample size and the accept and reject numbers used at incoming or final inspection.

What is the full form of AQL?

AQL stands for acceptable quality limit. Older documents call it acceptable quality level, and both terms refer to the same sampling concept.

How is AQL calculated?

You do not calculate AQL directly. You pick the lot size, inspection level and AQL value, then read the sample size code letter, sample size and accept number from the ISO 2859-1 or ANSI Z1.4 tables.

AQL vs LTPD: what is the difference?

AQL protects the supplier by defining a defect rate that should usually be accepted. LTPD, the lot tolerance percent defective, protects the buyer by defining a poor defect rate that should usually be rejected.

What is an AQL example?

For a lot of 1,000 parts at general inspection level II and AQL 1.0, the table gives a sample of 80 parts. The lot is accepted with 2 or fewer defectives and rejected with 3 or more.

Which AQL is used for critical, major and minor defects?

Common practice is zero acceptance for critical defects, AQL 1.0 or 1.5 for major defects and AQL 2.5 or 4.0 for minor defects. The final values should be agreed with the customer.

What standards define AQL sampling?

The main standards are ISO 2859-1 and ANSI/ASQ Z1.4 for attributes, and ISO 3951 or ANSI/ASQ Z1.9 for variables. They give matching sample tables and switching rules.

What are common AQL mistakes?

Typical mistakes include:

  • Treating AQL as a guaranteed defect rate
  • Ignoring switching rules to tightened inspection
  • Using one AQL for all defect types
  • Not taking random samples

Put Acceptable Quality Limit (AQL) Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.