What Is Gauge R&R?

Definition

Gauge R&R (Gauge Repeatability and Reproducibility) is a study that measures how much of the variation in measurement results comes from the measurement system itself rather than from the parts being measured.

Gauge R&R in Simple Terms

If a gauge gives different readings for the same part, you cannot trust any decision based on it. Gauge R&R splits measurement variation into two parts:

  • Repeatability (equipment variation): the same person measuring the same part several times with the same gauge.
  • Reproducibility (appraiser variation): different people measuring the same parts.

It is one part of Measurement System Analysis, described in the AIAG MSA reference manual.

How It Works

A common study uses 10 parts, 3 appraisers and 2 or 3 trials each, with parts measured in random order. Results are analysed with the average and range method or ANOVA. AIAG guidance for percent GRR:

% GRRGeneral guidance
Under 10 percentGenerally acceptable
10 to 30 percentMay be acceptable depending on the application, cost and risk
Over 30 percentGenerally unacceptable; improve the measurement system

The number of distinct categories (ndc) should be 5 or more.

Example

A study on a bore gauge gives 24 percent GRR, with most variation coming from reproducibility. The team finds that operators position the gauge differently. A fixture and a short training session bring GRR down to 8 percent.

Why It Matters

A poor gauge can reject good parts, accept bad ones and make Cp and Cpk results meaningless. Gauge R&R is expected for gauges in the control plan under IATF 16949. For variable data use Gauge R&R; for pass/fail checks use attribute agreement analysis. OperaHive calibration management software manages Gauge R&R and MSA records alongside calibration.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

What is an acceptable Gauge R&R?

Under AIAG guidance, under 10 percent is generally acceptable, 10 to 30 percent may be acceptable depending on the application, and over 30 percent is unacceptable.

What is the difference between Gauge R&R and calibration?

Calibration checks a gauge against a known reference standard. Gauge R&R checks how consistent the whole measurement process is, including the people using the gauge.

What is Gauge R&R?

Gauge R&R (gauge repeatability and reproducibility) is a measurement system analysis study that estimates how much of the observed variation comes from the measurement system rather than the parts themselves.

What does Gauge R&R stand for?

R&R stands for repeatability and reproducibility. Repeatability is variation when one operator measures the same part repeatedly with one gauge. Reproducibility is variation between different operators measuring the same parts.

What is an acceptable Gauge R&R percentage?

Under the AIAG MSA guidelines, below 10 percent is acceptable, 10 to 30 percent may be acceptable depending on the application and cost, and above 30 percent is unacceptable and the system needs improvement.

How do you perform a Gauge R&R study?

A typical study uses 10 parts, 3 operators and 2 or 3 trials each. Parts are measured in random order without operators seeing earlier results, then the data is analysed with the average and range or ANOVA method.

What is the difference between the ANOVA and average and range methods?

Both estimate repeatability and reproducibility. ANOVA also separates the operator and part interaction and is generally more accurate, while the average and range method is simpler to calculate by hand.

What is ndc in Gauge R&R?

ndc (number of distinct categories) shows how many groups of parts the measurement system can reliably tell apart. AIAG recommends an ndc of 5 or more for a measurement system to be acceptable.

Is Gauge R&R required for PPAP?

Yes. Measurement system analysis, usually including Gauge R&R studies, is one of the PPAP elements and is required by IATF 16949 for gauges listed in the control plan.

How often should Gauge R&R be done?

Gauge R&R should be done for new gauges, after repairs or significant changes, when new operators or methods are introduced, and at intervals set by the quality plan, often annually.

What do you do if Gauge R&R fails?

If repeatability is high, look at the gauge itself, fixturing or resolution. If reproducibility is high, focus on operator training and a clearer measurement method. Repeat the study after improvements.

Put Gauge R&R Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.