What Is Calibration?

Definition

Calibration is the comparison of a measuring instrument against a reference standard of known accuracy, to find and record how far its readings are from the true value. Adjustment, if needed, is a separate step.

Calibration in Simple Terms

Every inspection decision depends on the gauge being right. Calibration proves that a caliper, micrometer, torque wrench or CMM reads within its allowed error. The reference standards must be traceable to national or international standards, usually through an accredited lab working to ISO/IEC 17025.

ISO 9001, IATF 16949 and AS9100 all require measuring equipment to be calibrated or verified at set intervals, identified with its status and protected from adjustments that would make results invalid.

Key Elements

  • A unique ID for every gauge and a master list of all gauges.
  • A calibration interval based on use, risk and history.
  • A calibration record showing as-found and as-left readings, the standard used and its traceability.
  • A status label or system flag so expired gauges are not used.
  • A procedure for gauges found out of tolerance.

Example

A bore gauge comes back from calibration reading 0.015 mm low. Because it was used to accept parts since the last calibration, the quality team reviews the parts measured in that period, finds two lots close to the lower limit, and re-inspects them with a good gauge before deciding whether the customer must be told.

Common Mistakes

  • Recording only pass or fail, with no as-found readings.
  • Not assessing product measured with a gauge later found out of tolerance.
  • Forgetting employee-owned tools and test software.
  • Fixed intervals that are never reviewed against history.

Calibration covers accuracy, while MSA checks the whole measurement system, including bias. OperaHive calibration management software tracks schedules, due dates and certificates and helps investigate failed gauges.

FAQ

Frequently Asked Questions

Still unsure? Ask our team.

How often should gauges be calibrated?

There is no single rule. Intervals depend on how often the gauge is used, how critical the measurement is and its calibration history. Annual is common, with shorter intervals for heavily used gauges.

Is calibration the same as adjustment?

No. Calibration measures and records the error. Adjustment changes the instrument to reduce the error, and should be followed by a new calibration.

What is calibration in manufacturing?

Calibration is the comparison of a measuring instrument against a reference standard of known accuracy to find and record its error. It shows whether the instrument still measures within its stated tolerance.

What is traceable calibration?

Traceable calibration links a measurement through an unbroken chain of comparisons to national or international standards. Each step in the chain has a stated uncertainty and is documented on the certificate.

What does ISO 9001 require for calibration?

ISO 9001 requires measuring equipment used to verify product conformity to be calibrated or verified at set intervals against traceable standards, identified with its status and protected from adjustments that would invalidate results.

What should a calibration certificate include?

A calibration certificate should include:

  • instrument identification
  • date and calibration method
  • reference standards used and their traceability
  • as-found and as-left results
  • measurement uncertainty
  • the laboratory and person responsible
What happens if a gauge fails calibration?

Assess every measurement made with the gauge since its last good calibration. If suspect product may have shipped, decide whether to recall, re-inspect or notify the customer, and record the impact assessment.

What is the difference between calibration and verification?

Calibration measures and records the error of an instrument against a standard. Verification checks that the instrument meets specified requirements, often a pass or fail against a tolerance, and may use calibration results.

Who is responsible for calibration?

The quality department usually owns the calibration system, including the gauge register, intervals and records. The work itself may be done by an internal lab or an accredited external calibration laboratory.

What is calibration management software?

Calibration management software keeps a register of gauges, schedules due dates, stores certificates and flags overdue or failed instruments. It replaces spreadsheets and makes calibration status easy to show during audits.

Put Calibration Into Practice

Book a demo and see how OperaHive handles this on your own parts, processes and documents.